OPTIMASI PEMAKAIAN JAM KERJA DAN BAHAN BAKU DALAM MEMPRODUKSI MINUMAN INSTAN TRADISIONAL

Sondang Kiki Rosita, Totok Herwanto, Ahmad Thoriq, Boy Macklin Pareira

Abstract


CV. Cihanjuang Inti Teknik is a small or medium-sized business (UKM) engaged in the traditional beverage processing industry. The company is faced with problems of use to optimize the use of work time so that there is no idle work time or overtime working hours. Other problems, so far the procurement of raw materials carried out is also only based on estimates, namely with raw materials made in stock without taking into account quantitative calculations. The goal programming method is used with the aim of analyzing and describing the optimal use of resources in working hours and raw materials from the average production target needed by the company. The calculation of goal programming is supported by using LINDO (Linear Interactive Discrete Optimizer) program to obtain the optimal number of products from working hours and raw materials needed by the company. The results of the study obtained optimal regular working hours in scenarios I, II, III, and IV respectively in the amount of 159.95 hours/month, 174.25 hours/month, 176.26 hours/month and 192.37 hours/month. There was also an increase in the use of raw materials for ginger, coffee, ginseng and pepper in scenario II, raw materials for ginger, white and vanilla sugar in scenario III, raw materials for white sugar, vanilla and cinnamon in scenario IV.


References


Andini dan Slamet. 2016. Analisis Optimasi Persediaan Bahan Baku dengan Menggunakan Metode Economic Order Quantity pada CV. Tenun/ Atbm Rimatex Kabupaten Pemalang. Management Analysis Journal, 5 (2), 143-148.

D. Cahaya N., I. Santoso, and M. Effendi, “Perencanaan Produksi Keripik Kentang Menggunakan Metode Fuzzy Linear Programming (FLP) (Studi Kasus di UKM Agronas Gizi Food Kota Batu),” no. December 2014, pp. 1–7, 2014.

Devani. 2013. Optimasi Perencanaan Produksi dengan menggunakan Metode Goal Programming. Jurnal Sains,11(1), 84-91.

Novitasari, N. 2013. Penggunaan Metode Goal Programming Untuk Optimasi

Perancangan Proses Produksi Produk Wingko Babat. Applied Industrial

Engineering Journal, 1(2), 47-52.

Novitasari. 2013. Pendekatan metode goal programming dalam optimasi perencanaa produksi. Jurnal Mahasiswa Matematika, 1(3), 176-179.

Nursanti E, Purnam, R.Suardika,I. 2015. Optimasi kapasitas produksi untuk mendapatkan keuntungan maksimum dengan Linear Programming. Jurnal Performa 14(1), 61-68

Pangabean, D. 2014. Optimasi perencanaan keuntungan produksi pada pengolahan rending di perusahaan “rendang erika” payakumbuh. Jurnal Optimasi Sistem Industri, 13(1), 427-253.

Sugiyono. 2014. Metode Penelitian Kuantitatif, Kualitatif, dan Kombinasi (Mix Methods). Bandung: Alfabeta.

Supriyanto. 2014. Otimasi Waktu/Proses Produksi di PT. Sumiden Sintered Component Indonesia dengan Teknik Analisa Network/Pert dan Metode Smed. Jurnal PASTI 8(3), 362 – 398.

Susanti R. 2013. Optimasi Perencanaan Produksi untuk produk Pesanan Pada Perusahaan Pestisida Menggunakan Metode Goal Programming. Jurnal Teknik Industri. 2(1), 1-10.




DOI: https://doi.org/10.21107/agrointek.v13i2.5052

Refbacks

  • There are currently no refbacks.




Copyright (c) 2019 AGROINTEK

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Indexed by

Crossref logo

Mailing Address:

Agrointek: Jurnal Teknologi Industri Pertanian

Department of Agroindustrial Technology, Faculty of Agriculture, University of Trunojoyo Madura
Raya Telang St. PO BOX 2, Kamal - Bangkalan - Jawa Timur
Phone: (031) 3013234, Email:agrointek@trunojoyo.ac.id

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License