Pengaruh Variasi Holding Time pada Proses Single Stage Aging Terhadap Kekerasan dan Mikrostruktur pada Material Paduan Al-Si-Cu-Fe

Apang Djafar Shieddieque; Rendi Kuswandi

doi:10.21107/rekayasa.v18i1.26678

Pengaruh Variasi Holding Time pada Proses Single Stage Aging Terhadap Kekerasan dan Mikrostruktur pada Material Paduan Al-Si-Cu-Fe

Apang Djafar Shieddieque, Rendi Kuswandi

Abstract

The Al-Si-Cu aluminum alloy is the most commonly used alloy for household appliances, aircraft materials, automotive, marine vessels, construction, and more. However, cast aluminum alloys still exhibit low mechanical properties, necessitating additional processes to enhance their strength. One method of strengthening aluminum is by varying the composition and/or heat treatment process. The aim of this research is to investigate the effect of aging time variation on the microstructure and hardness of the Al-Si-Cu-Fe alloy. The heat treatment processes conducted in this study include solid solution treatment (T=540°C and t=5 hours) and various single-stage aging treatments (T=155°C and t=4, 5, and 6 hours). Mechanical properties of the aluminum alloy were evaluated through metallographic observations and Brinell hardness testing. Microstructural observations indicate changes in the Silicon microstructure from the As cast sample, which exhibits dendrites, to the formation of AlSi and AlFeSi phases after aging treatment. With longer aging treatments, larger and more dispersed precipitate grains are formed. The variation in holding time has different effects on hardness, with the highest hardness obtained at a holding time of 4 hours during artificial aging, resulting in 71.57 BHN. However, increasing the holding time tends to decrease hardness due to the growth of larger precipitate phases.

Keywords

artificial aging, holding time, metallography, hardness testing, solid solution treatment

Full Text:

PDF (Bahasa Indonesia)

References

ASM Handbook Volume 3: Alloy Phase Diagrams - ASM International (Vol. 7). (2004). ASM Internasional. https://www.asminternational.org/search/-/journal_content/56/10192/25871543/publication

Budiarto, B., Antonius, D., & Putra, B. A. (2020). Analisis Pengaruh Waktu Artificial Age Terhadap Kekerasan, Densitas Dan Struktur Kristal Paduan Alumunium (7075) Untuk Bahan Sirip Roket. Jurnal Kajian Ilmiah, 20(1), 13–28. https://doi.org/10.31599/jki.v20i1.67

Elsebaie, O., Samuel, A. M., Samuel, F. H., & Doty, H. W. (2014). Impact toughness of Al-Si-Cu-Mg-Fe cast alloys: Effects of minor additives and aging conditions. Materials and Design, 60, 496–509. https://doi.org/10.1016/j.matdes.2014.04.031

Fallahi, A., Hosseini-Tudeshky, H., & Ghalehbandi, S. M. (2014). Effect of heat treatment on mechanical properties of ECAPed 7075 aluminum alloy. Advanced Materials Research, 829(January 2017), 62–66. https://doi.org/10.4028/www.scientific.net/AMR.829.62

Liu, Y., Pan, Q., Li, H., Huang, Z., Ye, J., & Li, M. (2019). Revealing the evolution of microstructure, mechanical property and corrosion behavior of 7A46 aluminum alloy with different ageing treatment. Journal of Alloys and Compounds, 792, 32–45. https://doi.org/10.1016/j.jallcom.2019.03.324

Mineral, K. E. dan S. D. (2021). Panduan Evaluasi Sistem Pengolahan Aluminium. 1–37. www.ebtke.esdm.go.id

Muttahar, M. I. Z. (2019). Pengaruh Variasi Waktu Holding Proses Artificial Aging Terhadap Kekuatan Tarik Dan Ketahanan Impak Paduan Al-Si Effect Of Holding Time During Artificial Aging Of Al-Si Alloy. 41, 69–74.

Muttahar, M. I. Z., Virdhian, S., Putra, P. A., Djuanda, D. R., Afrilinda, E., & Genesar, A. (2020). Mechanical Properties Enhancement Of Al-Si-Cu-Fe Alloy Through Aging Treatment Variations. 24(1), 67–84.

Nurhidayat, M. (2017). Pengaruh Arus dan Waktu Anodisasi Terhadap Kekerasan Pada Lapisan Oksida Alumunium. Jurnal Tekhnik Mesin.

Paramartha, I. G. B. (2016). Studi Eksperimental Pengaruh Perlakuan Panas Precipitation Hardening T6 Dengan Variasi Holding Time Dan Temperatur Solution Treatment Terhadap Sifat Mekanik Paduan Aluminium Adc 12 Experimental Study on the Effect of Precipitation Hardening T6 Paired With. Tugas Akhir– Tm141585. https://repository.its.ac.id/1184/1/2111100046-Undergraduate_Theses.pdf

Perwakilan, D., & Republik, R. (2022). Miliki Cadangan Bauksit Terbesar di Dunia , Legislator Sayangkan Indonesia Impor Aluminium. 2–3.

Pranata, M. D. E., Alfirano, & Mujiat, J. (2018). Analisis Struktur Mikro Dan Sifat Mekanik Paduan Al 2014 Hasil Proses Aging Dengan Variasi Temperatur Dan Waktu Tahan. Jurusan Teknik Metalurgi Universitas Sultan Ageng Tirtayasa, 1(1), 1–9.

Putra, P. A., Krisnadi, L., Muttahar, M. I. Z., Abdullah, H., & Amalia, D. (2020). Pengembangan Boogie Wheel Tank AMX-13 untuk Komponen Kendaraan Tempur Tank Jenis Ringan. Jurnal Teknologi Bahan Dan Barang Teknik, 10(2), 100–109. https://doi.org/10.37209/jtbbt.v10i2.186

Rahmawati, Z. S. (2010). Pengaruh Putaran Terhadap Kekuatan Tarik Pada Friction Welding Aa 2024 –T3 Dengan Aa 6061 –T6. 5–20. https://lib.ui.ac.id/file?file=digital/132994-T 27820-Analisis pengaruh-Tinjauan literatur.pdf

Septian, M. F. (2022). Pengaruh Variasi Temperatur Artificial Aging Pada Aluminium 6061 Terhadap Sifat Kekerasan the Effect of Artificial Aging Temperature Variations on Aluminum 6061 on Hardness and Micro Structure. Universitas Lampung.

Setiadi, B., Martupa, L., Lumban, D., Moh, J., Ii, K., Sawah, S., & Selatan, J. (2022). Analisa Sifat Mekanis Velg Aluminium Sepeda Motor Menggunakan Metode Heat Treatment Dengan Variasi Waktu Kelipatan 3 Jam Pada Suhu Aging 150oC. Sainstech: Jurnal Penelitian Dan Pengkajian Sains Dan Teknologi, 32(Vol. 32 No. 4 (Desember 2022)), 64–73. https://doi.org/10.37277/stch.v32i4.1474

Shieddieque, A. D., Suratman, R., & Widyanto, B. (2020). Effect of Alkaline Treatment and Fiber Orientation on Mechanical Properties of Biocomposite Sansevieria trifasciata Fibre / Vinyl Ester. 62(05), 2631–2637.

Shieddieque, A. D., Tinggi, S., Wastukancana, T., Virdhian, S., Industries, M., Jatira, J., Tinggi, S., & Wastukancana, T. (2021). Effect of non-isothermal aging on microstructure and impact toughness of Al – Si – Cu – Fe cast alloy. November. https://doi.org/10.1063/5.0066662

Shieddieque, A. D., Virdhian, S., Muttahar, M. I. Z., Jatira, Akbar, M. R., & Kanestu, G. D. (2021). Effect of non-isothermal aging on microstructure and impact toughness of Al-Si-Cu-Fe cast alloy. AIP Conference Proceedings, 2338. https://doi.org/10.1063/5.0066662

Surdia, T. (2004). Klasifikasi Paduan Aluminium.

Tash, M., Samuel, F. H., Mucciardi, F., & Doty, H. W. (2007). Effect of metallurgical parameters on the hardness and microstructural characterization of as-cast and heat-treated 356 and 319 aluminum alloys. Materials Science and Engineering A, 443(1–2), 185–201. https://doi.org/10.1016/j.msea.2006.08.054

Vandersluis, E., & Ravindran, C. (2020). Effects of solution heat treatment time on the as-quenched microstructure, hardness and electrical conductivity of B319 aluminum alloy. Journal of Alloys and Compounds, 838, 155577. https://doi.org/10.1016/j.jallcom.2020.155577

Yang, J., Ni, Y., Li, H., Fang, X., & Lu, B. (2023). Heat Treatment Optimization of 2219 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing. Coatings, 13(3). https://doi.org/10.3390/coatings13030610

Yang, Z., & Banhart, J. (2021). Natural and artificial ageing in aluminium alloys – the role of excess vacancies. Acta Materialia, 215, 117014. https://doi.org/10.1016/j.actamat.2021.117014

Yunus, M., & Alamro, T. (2022). Evaluation of wear and corrosion properties of FSWed aluminum alloy plates of AA2020-T4 with heat treatment under different aging periods. Reviews on Advanced Materials Science, 61(1), 687–697. https://doi.org/10.1515/rams-2022-0261

Zhou, J., Miao, J., Wang, B., & Wang, J. (2022). Effect of Solution Treatment and Aging Treatment on Mechanical Properties of 2060 Al-Li Alloy and Process Multi-Objective Optimization. Metals, 12(6). https://doi.org/10.3390/met12060897

Zulfia, A., Juwita, R., Uliana, A., Jujur, I. N., & Raharjo, J. (2010). Proses Penuaan (Aging) pada Paduan Aluminium AA 333 Hasil Proses Sand Casting. Jurnal Teknik Mesin, 12(1), 13–20. https://doi.org/10.9744/jtm.12.1.13-20