Direct On Line Circuit as a 3 Phase Motor Controller Using the Siemens S7 1200 Programmable Logic Controller

Sherlly Dwi Anggrainy, Haris Abizar, Jan Manendro Budi Utomo

Abstract


In today's world of education, teachers are required to be creative in the teaching process. Teachers are very influential in the development of education in Indonesia. One indicator of a country's progress can be seen from education. This research uses descriptive experimental research that uses a qualitative approach. This research is descriptive because this research does not use a particular method but only uses existing facts and is temporary. The DOL Circuit System is used in three-phase induction motor starting systems and is designed to minimize very high starting current surges. The three-phase induction motor starter system with the DOL circuit works directly to provide 380 VAC voltage to the motor coil so that the motor rotates immediately. The first condition is when the MCB is activated the L2 lamp output immediately activates as a sign that the DOL circuit is on standby. Then the second condition describes the circuit when the MCB is active and S2 is pressed, K1 will be active so that the resulting output is L3 on. Entering the third condition shows that the MCB remains active and S1 is pressed, the output that occurs is L2 lights up. The fourth condition where the MCB remains on then EMG is activated, the output that occurs is L4 lights up. In the fifth condition, the MCB remains on and the TOR is activated, so that the outputs, namely L1 and L2, light up simultaneously.

Keywords


Dol, Condition, PLC, Series, Siemens S7 1200

Full Text:

PDF

References


A. Effendi, “Perancangan Pengontrolan Pemanas Air Menggunakan PLC Siemens S7-1200 dan Sensor Arus ACS712,” vol. 2, no. 3, 2018.

S. Nuari, Atmam, and E. Zondra, “Analisis Starting Motor Induksi Tiga Phasa Menggunakan Programmable Logic Controller (PLC),” SainETIn, vol. 2, no. 2, pp. 60–67, 2018, doi: 10.31849/sainetin.v2i2.2019.

I. M. Gde Arjana, A. A., Sukada, J.M., Suratma, N.A., Dwinata, “Prosiding Seminar Nasional Sains dan Teknologi,” Pengemb. Buah Pinang sebagai Anthelintika dalam upaya Meningkat. Produkt. Ternak, no. Petruzella 2010, pp. 215–220, 2014.

T. Tohir Politeknik Negeri Bandung Jl Geger Kalong Hilir Ds Ciwaruga, “Rancang Bangun Kendali Motor Induksi 3 Fasa Berbasis PLC Dengan Metoda Pemograman Function Block Diagram Control Design of 3 Phase Induction Motor Based PLC with Programming Function Block Diagram,” no. November 2019, pp. 501–511, 2019.

H. Mandala, H. Rachmat, D. Sukma, and E. Atmaja, “Perancangan Sistem Otomatisasi Penggilingan Teh Hitam Orthodoks Menggunakan Pengendali PLC Siemens S7 1200 dan Supervisory Control and Data Acquisition ( SCADA ) di PT . Perkebunan Nusantara VIII Rancabali,” J. Tugas Akhir | Fak. Rekayasa Ind., vol. 2, no. 1, pp. 1–8, 2015.

A. Salkic, H. Muhovic, and D. Jokic, “Siemens S7-1200 PLC DC Motor control capabilities,” IFAC-PapersOnLine, vol. 55, no. 4, pp. 103–108, 2022, doi: 10.1016/j.ifacol.2022.06.017.

M. Adjie and A. Dwi, “Analisa Sistem Starting DOL (Direct On Line) pada Motor Listrik PT. Semen Baturaja,” J. Multidisipliner Bharasumba, pp. 395–402, 2022.

P. Asmaleni, D. Hamdani, and I. Sakti, “Pengembangan Sistem Kontrol Kipas Angin Dan Lampu Otomatis Berbasis Saklar Suara Menggunakan Arduino Uno,” J. Kumparan Fis., vol. 3, no. 1, pp. 59–66, 2020, doi: 10.33369/jkf.3.1.59-66.

I. . Shaputra.R, Gunoto.P, “Kran air otomatis pada tempat berwudhu menggunakan sensor ultrasonik berbasis arduino uno,” Sigma Tek., vol. 2, no. 2, pp. 192–201, 2019.

C. Chan, K. Chow, S. Yiu, and K. Yau, “Enchancing The Security And Forensic Capabilities of Programmable Logic Controllers,” Springer Nat. Switz., pp. 351–367, 2018.

E. Sutriani and R. Octaviani, “Analisis Data dan Pengecekan Keabsahan Data”.

muhammad khadafi alkindi, “Perancangan Alat Detektor Kegagalan Fasa Sebagai Proteksi Beban 3 Fasa,” Peranc. Alat Detektor Kegagalan Fasa Sebagai Prot. Beban 3 Fasa, vol. 92, 2018.

B. Suriansyah, “Catu Daya Cadangan Berkapasitas 100 Ah / 12 V untuk Laboratorium Otomatisasi Industri Poliban,” INTEKNA, no. 2, p. ., 2019.

Z. Anthony, “Pengembangan Rangkaian Kendali untuk Mengoperasikan Motor Induksi3-Fasa,” vol. 6, no. 1, pp. 81–86, 2017.

I. J. Prakoso, A. Warsito, and T. Sukmadi, “Perancangan Pengasutan Bintang – Segitiga dan Pengereman Dinamik pada Motor Induksi 3 Fasa dengan Menggunakan Programmable Logic Controller ( PLC ),” vol. 14, no. 1, pp. 13–19, 2012.

E. Susanto, “Automatic Transfer Switch (Suatu Tinjauan),” J. Tek. Elektro Unnes, vol. 5, no. 1, pp. 3–6, 2013.

I. G. S. Sudaryana, “Pemanfaatan Relai Tunda Waktu dan Kontaktor pada Panel Hubung Bagi (PHB) untuk Praktek Penghasutan Starting Motor Star Delta,” 2019.

R. S. Rizqyka Amalia, Hendro Widiarto, “Modifikasi alat kendali,” Modif. Alat Kendali Air Cond. Split Di Lab. Maint. Airf. Gr. Light. Sekol. Tinggi Penerbangan Indones., vol. 13, no. 1, p. 73, 2020.

A. F. Kheiralla, O. Siddig, A. A. E. Mokhtar, M. Esameldeen, and O. Addalla, “Design and Development of a Low Cost Programmable Logic Controller Workbench for Education Purposes,” Int. Conf. Eng. Educ. – ICEE 2007, pp. 1–6, 2007.

A. M. Muhammad, “Simulasi Alat Penjaring Ikan Otomatis Dengan Penggerak Motor Servo Continuous, Sensor Jarak Hc- Sr04 Dan Tombol, Menggunakan Arduino Mega,” Simulasi Alat Penjaring Ikan Otomatis Dengan Penggerak Mot. Servo Contin. Sens. Jarak Hc-Sr04 dan Tombol, Menggunakan Arduino Mega, vol. 12, no. 1, pp. 39–47, 2019.

E. Gunawan and E. Wahyono, “Jalan Umum Dengan Sistem Kontaktor,” Jalan Umum Dengan Sist. Kontaktor, vol. 1, no. 1, pp. 36–44, 2017.




DOI: https://doi.org/10.21107/triac.v12i2.32088

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 Jurnal Teknik Elektro dan Komputer TRIAC

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Creative Commons License
Indexed by: